GRIDSINE-X
Premium SiC AHF Series

Silicon Carbide switching device. > 100 kHz switching frequency, 4 µs instantaneous response, up to 98% efficiency. Dedicated active harmonic filter for steel mills, arc furnaces and other severe harmonic loads.

4 µs response > 100 kHz switching up to 98% efficiency 2nd – 51st harmonic
Silicon Carbide switching
4 µs instantaneous response
2nd – 51st harmonic (independent)
Up to 10 modules in parallel
Active Power Quality

SiC harmonic filter
for arc furnaces and presses

GRIDSINE-X is the active harmonic filter of the Premium SiC Series. It uses Silicon Carbide switching devices with firmware set up for harmonic filtering only, on 220V to 380V heavy industrial systems.

Modules are rated 20 A to 200 A. With filtering effectiveness of up to 98%, THDi at the point of common coupling drops below 5%. Instantaneous response is 4 µs, so transient harmonics are cancelled before they spread through the network.

Filtering covers the 2nd to 51st harmonic, each order selectable on its own. This targets the spectrum that arc furnaces, large presses and crane drives actually produce.

SiC switching 4 µs instantaneous > 100 kHz switching 2nd–51st harmonic up to 98% filtering Bluetooth + APP
4 µs
Instantaneous response
to grid transients
200 A
Max module capacity
up to 98%
Filtering effectiveness
51st
Highest filtered harmonic
(independent per order)
Technical Specifications

GRIDSINE-X Specification

Values from the GRIDSINE-X datasheet. 220V to 380V, 20 A to 200 A modules.

ParameterSpecification
Product seriesGRIDSINE-X — Premium SiC Active Harmonic Filter (AHF)
Control algorithmCurrent dual closed-loop active damping
Switching deviceSilicon Carbide (SiC)
FunctionAHF (Active Harmonic Filtering) — dedicated mode
Operating voltage220V ~ 380V
Frequency50 / 60 Hz
Connection type3-Phase 3-Wire (3P3W) and 3-Phase 4-Wire (3P4W)
Module capacity20 · 35 · 50 · 75 · 100 · 200 A
Instantaneous response4 µs
Full response time1/4 cycle (harmonic) / 1 cycle (fundamental)
Switching frequency> 100 kHz
System efficiency≥ 98%
Harmonic filtering range2nd – 51st harmonic (independent per-order selection)
Filtering effectiveness≥ 98%
THDi target< 5% at PCC
Resonance suppressionActive suppression
3-Phase load balancingYes — active phase and neutral current balancing
Max. parallel modulesUp to 10 modules (smart rotation)
Overload capacity110% Continuous
Operating temperature−10°C ~ +40°C (derating 2.5%/°C from 40°C to 50°C)
Communication interfaceBluetooth / Mobile APP, RS485 / CAN / RJ45
IP protectionIP20
StandardsIEC 61000 / IEEE 519
Key Features

SiC switching, 4 µs response, 51 harmonic orders

4 µs Instantaneous Response

The SiC stage reacts to arc furnace transients, crane impacts and press cycles in 4 microseconds, before the disturbance reaches the grid.

> 100 kHz Switching Frequency

SiC switches at over 100 kHz. The compensation current is closer to a clean sine wave, so cancellation is more exact at every order.

2nd to 51st harmonic, independent selection

Filtering covers the 2nd to the 51st order. Each order can be enabled or disabled on its own, so the filter is tuned to the measured load profile.

up to 98% Filtering Effectiveness

Filtering effectiveness up to 98% at rated capacity. THDi at the PCC falls below 5%, including on arc furnace and rolling mill feeders.

Smart Rotation Redundancy

Up to 10 modules in parallel with smart rotation, which spreads operating hours evenly. A faulty module isolates itself and the others raise their output.

Bluetooth + Mobile APP Control

Harmonic priorities, filtering targets and load sharing ratios are set and monitored from the mobile application over Bluetooth.

Module Variants

Six module sizes, 20 A to 200 A

20, 35, 50, 75, 100 and 200 A on the same SiC platform. Capacities can be mixed within one parallel group of up to 10 modules.

20
A
SiC · > 100 kHz4 µs response220V–380V
35
A
SiC · > 100 kHz4 µs response220V–380V
50
A
SiC · > 100 kHz4 µs response220V–380V
75
A
SiC · > 100 kHz4 µs response220V–380V
100
A
SiC · > 100 kHz4 µs response220V–380V
200
A
SiC · > 100 kHz4 µs response220V–380V

All modules: IP20 · 3P3W / 3P4W · Bluetooth / Mobile APP, RS485 / CAN / RJ45 · IEC 61000 / IEEE 519
Mixed-capacity parallel operation, up to 10 modules per group

Applications

Applications: arc furnaces, presses and crane drives

Three cases where the 4 µs response or the per-order selection decides the choice.

Steel & Arc Furnaces

Arc furnaces are the harshest harmonic source. The 4 µs SiC response cancels their harmonics before they distort the voltage for neighbouring equipment.

Rolling Mills

Large motor drives and crane systems on one bus. Independent per-order selection targets the spectrum each load produces.

Automotive

Welding lines, paint line rectifiers and large press drives produce transient harmonics. The 4 µs instantaneous response and quarter-cycle full response cancel them.

Need standard IGBT for a more cost-sensitive project, or the ultra-compact 88 mm form factor for a retrofit? Compare GRIDSINE-X with the full GRIDSINE lineup.

Compare all GRIDSINE models

Send your THDi measurement and the harmonic orders present. We size the SiC modules and quote the cabinet.

Module count, redundancy and cabinet layout follow from the harmonic measurement data. Sizing is free of charge before any commitment.

Documents

Technical documents for this product. Ask for a document still in preparation and we will send it as soon as it is ready.

Request a Quote — GRIDSINE-X

We reply within 1 business day. Urgent: +90 850 840 64 24

By submitting this form you agree to be contacted by Forte Teknik Makine A.Ş. Your data will not be shared with third parties.

Response within 1 business day